AlphaBot Bluetooth - Arduino Robot Building Kit with Sensors

Brand: Waveshare
Product Code: WSR-08358
Availability: Vilnius Store In Stock
Kaunas Store Out of Stock
108.70€
Ex Tax: 89.84€

Qty

This kit comes with controller board UNO PLUS, AlphaBot robotic platform (line tracking, obstacle avoidance, speed measuring, IR control), ultrasonic sensor, Bluetooth module, and a versatile Arduino accessory shield.
While utilizing UNO PLUS as controller board, this kit is based on the Arduino software/hardware open source platform. Combined with the modular design, it's an ideal platform to get started with Arduino robot.


UNO PLUS Features
UNO PLUS is a development board compatible with the Arduino UNO R3, an improved & enhanced alternative solution for Arduino UNO R3.


AlphaBot Features
•    Raspberry Pi/Arduino interfaces, works with either one separately, or both
•    Arduino extend header, supports Arduino shields
•    Modular design, plug-and-play modules like line tracking, obstacle avoidance, speed measuring, etc. eliminating the trouble of connecting mess wires.
•    LM298P motor driver with diode protection circuit, more safety
•    LM2596 voltage regular, provides stable 5V power to the Raspberry Pi/Arduino
•    TLC1543 AD acquisition chip, allows the Pi to use analog sensors


Accessory Shield Overview
•    Accessory Shield integrates common used accessories/components listed as follows :
•    Joystick (5 directions)
•    Adjustable potentiometer
•    Buzzer
•    RGB LED
•    Temperature sensor
•    3-axis digital accelerometer
•    High precision RTC
•    0.96inch OLED
•    XBee interface


What's on the UNO PLUS
•    ATMEGA328P-AU
•    AMS1117-3.3 : 3.3V voltage regulator
•    NCP1117ST50T3G : 5V voltage regulator
•    FT232RL : USB to UART convertor
•    Arduino interface
•    compatible with standard Arduino interface with two additional analog inputs A6 (config the CFG), A7
•    solder pads provided, supports prototype breadboard
•    ICSP interface
•    MICRO USB connector : for uploading program OR serial port debugging
•    Power output header : 3.3V OR 5V, voltage level configured by the onboard power configuration switch, used as power output OR common-grounding with other boards
•    FT232 pins : for burning Bootloader into the microcontroller
•    DC input : 7V ~ 12V
•    Reset button
•    Power indicator
•    Serial port Rx/Tx indicator
•    User LED
•    500mA fast self-recovery fuse
•    Power configuration : for configuring the operating voltage
•    Bootloader selection switch
•    turn ON : the board will reset when power-up OR other USB devices were detected connecting to the PC
•    turn OFF : the onboard program runs immediately when power-up, and the board will not reset when other USB devices were detected connecting to the PC


What's on the AlphaBot Mainboard
•    Raspberry Pi interface: for connecting Raspberry Pi
•    Arduino interface: for connecting Arduino
•    Motor interface
•    Ultrasonic module interface
•    Servo module interface
•    Obstacle avoidance module interface
•    Speed measuring interface
•    Battery holder: supports 18650 batteries
•    Reserved power input (not soldered): for connecting other external power supply
•    Arduino expansion header: for connecting Arduino shields
•    UART interface: for connecting Bluetooth module, to control the robot remotely via Bluetooth
•    SPI interface: for connecting NRF24L01 wireless module
•    Line tracking module interface
•    TLC1543: 10-bit AD acquisition chip, allows the Pi to use analog sensors
•    LM298P: dual H bridge motor driver chip, up to 2A current
•    Anti-reverse diode
•    Power switch
•    LM2596: 5V regulator
•    Power indicator
•    UART switch: turn on to enable serial communication between Raspberry Pi and Arduino
•    IR receiver: control the robot remotely via infrared
•    Raspberry Pi/Arduino selection: select the Raspberry Pi or Arduino to control the robot peripherals


Development Resources
•    Wiki : www.waveshare.com/wiki/AlphaBot
•    Wiki : www.waveshare.com/wiki/UNO_PLUS