LOKLiK Auto Mug Heat Press

The LOKLiK Auto Mug Heat Press is built for makers and small businesses who want consistent, professional-looking sublimation mugs without babysitting a manual press. It handles the clamping, heating, and timing automatically, so every mug in a batch comes out with the same clean, vibrant transfer - whether it's a one-off gift or a full print run.

Basic mug presses tend to share the same shortcomings: pressure that's fixed and easy to over- or under-apply, no display to tell you what's actually happening during a press, and a one-piece body that's awkward to clean or repair. The LOKLiK Auto Mug Heat Press addresses each of these directly - pressing is automatic and hands-free, pressure is adjustable to match the mug you're working with, a real-time display shows temperature and pressure as the press runs, and the heat plate is a separate, replaceable module rather than a fixed part of the housing.

The workflow is short enough to learn in one attempt.

1. Load the module
Attach the right heat plate for what you're pressing

2. Wrap your design
Wrap the sublimation transfer around the blank

3. Insert and press
Set your parameters and let the machine take over

4. Enjoy the result
Crisp, vibrant transfers on mugs, jars, and tumblers alike

Four programmable preset slots let you save your go-to temperature, time, and pressure combinations - one for standard mugs, another for tumblers, another for a tricky material that needs its own settings. Once saved, switching between them is a single button press, instead of re-entering three numbers before every batch.

A tighter heating wrap around the mug lets designs run to within about 0.5 cm of the handle, so more of the printable area actually gets used instead of being lost to a wide, unheated margin near the handle.

Pressure can be set anywhere from 20 to 70 kg, so thin, delicate mugs and thicker, heavier ones can each get the right amount of clamping force. Too little pressure risks patchy, faded transfers
too much can stress the material. The real-time display shows the exact pressure being applied throughout the press, so you're never guessing.

Dialling in the right pressure for the material in hand makes the difference between a patchy transfer and a sharp, even, wrap-around print:

Lower pressure - suited to delicate or thin-walled items

Standard pressure - the right fit for most mugs and tumblers

Higher pressure - for a tight, gap-free wrap on sturdier items

The included heat plate module accommodates mugs from 8 to 8.8 cm in diameter, covering the great majority of standard ceramic mugs and coffee cups on the market without any adjustment needed. And because the heat plate is a detachable module rather than a fixed part of the machine, the same press can be adapted to different drinkware. The mug module is included in the box and ready to use out of the gate
modules for straight tumblers and for 1.2-litre handle tumblers are available separately.

For Mugs
Included in the box

For Straight Tumblers
Sold separately

For 1.2-Litre Handle Tumblers
Sold separately

Changing the module is a tool-free push-and-lock action - no screws, no separate tools, no waiting for anything to cool down first. That makes it realistic to switch between mugs and tumblers within the same crafting session instead of dedicating the machine to one product type.

Every module is built around an aluminium heating core rated for more than 10,000 presses - well beyond the 500 to 800 presses typical of basic entry-level machines. That means fewer replacements, lower running costs, and less risk of a worn-out plate causing bubbling or wrinkling mid-batch.

An even heat distribution around the whole mug helps avoid the cold spots and patchy colour that come from uneven manual pressing. A real-time display keeps temperature, time, and pressure visible throughout the cycle. A 15-minute auto shut-off switches the heating element off automatically if the press is left idle, adding a layer of safety for a busy home or workshop.

Whether it's a one-off gift or a shelf full of orders to fulfil, the same automatic press handles both without extra fuss.

Craft memorable, personalised gifts at home

Or scale up a small sublimation business

The LOKLiK Auto Mug Heat Press arrives ready to start pressing straight away: the machine itself, the mug heat plate module already sized for standard 8-8.8 cm mugs, both a 2 mm and a 4 mm heat press mat to suit different blanks, a pair of heat-resistant gloves, heat-resistant tape to secure your transfers, and a user manual to walk through setup. Everything needed for a first batch of mugs is in the box - additional heat plate modules for tumblers can be added later as your projects grow.

• LOKLiK Auto Mug Heat Press
• Mug heat plate module (8-8.8 cm diameter)
• 2 mm heat press mat
• 4 mm heat press mat
• Heat-resistant gloves
• Heat-resistant tape
• User manual

Note: heat plate modules for straight tumblers and for 1.2-litre handle tumblers are not included and are sold separately.

Claim orders from Stores

You can claim your purchased items within 1 - 4 work days after making an order (if product is in local warehouse).

Please wait for an email notification regarding Your order status update.

Vilnius Store address: Vytenio g. 20, LT-03229 Vilnius, Lietuva

Kaunas Store address: Pramonės pr. 4D, LT-51329, Kaunas, Lietuva

Local delivery in Lithuania

Purchased items are delivered locally through Venipak service. Depending on availability of items, orders are processed within 1-3 work days. Orders made until 1AM are shipped the same day.

Local delivery  (1-4 w.d.) price for items of any size is through through courier service is 4.90€ (incl. VAT), if the amount of the shopping cart exceeds 150€ - delivery is free.

Local delivery price to Venipak parcel terminals (1-3w.d.) is 2.90€ incl. VAT, if the amount of the shopping cart exceeds 50€ - delivery is free.

Local delivery price to Omniva parcel terminals (1-3w.d.) is 3.90€ incl. VAT,if the amount of the shopping cart exceeds 70€ - delivery is free.

Payment on delivery (COD) +2.00€ (incl. VAT).

You can pay for the goods at the time of delivery to the courier in cash or by credit card. Payment to Omniva parcel terminals is only possible by bank card.

A separate delivery fee applies to oversized items, regardless of the amounts and conditions stated above.

International delivery pricing through courier service

International shipping prices depend on geographic location:

Latvia - 5.50€ (incl. VAT)

Estonia - 6.50€ (incl. VAT)

Paid orders of more than 150€ are shipped for free to Latvia and Estonia.

other countries - negiotiated individually.

International delivery pricing to Omniva/Venipak parcel terminals

Latvia - 6.00€ (incl. VAT)

Estonia - 8.50€ (incl. VAT)

Payments:

We accept payments via PayPal for orders over 20€.